Видео

what engine stand did you use? looks like the $99 one from harbor freight maybe?

EXCELLENT VIDEO! I am in the market for a livescope and this mounting option is exactly what I was looking for! Thank you for the information. Going to the site now!

Wharever happened to this motor. I found video where you were going to epoxy some damage but couldn't find any rebuild video. Just curious

What type of battery -can I get a light auxiliary car battery or do I need a full deep marine?

Great vid!

"Danger, Will Robinson!" The positive wire from the battery to the pump should be fused at the battery end. I didn't hear it mentioned in the video, and the write-ups I've read don't mention it either. But ALL electrical feeds from the battery should be fused as close to the battery as possible. What size fuse? The pump mfr should have a rating for this. The reason for locating the relay in a compartment separate from the gas is because a spark will jump from one contact to the other as the contact closes. Not a big deal unless there are fuel vapors at a combustible ratio in the area of the relay. The same reason not to operate a light switch if you smell natural gas. FWIW ... My HPDI 150 died on the way from the launch to the cabin when I put the pontoon in the water this year. I had to be towed home. I suspect the LP pumps and ordered two before seeing this. This change likely will occur later when taking the boat out of the water. Thanks for the video! Nice job.

looking at this one -but their website is pretty poor on descriptions / pictures and this is the only video ive come across on how this works they really should link it from their site, I do like the idea for my tracker 175 but moving that plate is kinda difficult to do quickly at a dock etc --- any experience with the magnetic plate???? I dock my boat on the side Id be using so a quick way to move that plate out of the way would be better and I KNOW id drop those little screws in the water if thats they plan the really should include a lot of spares or at least tell you where to get them. looks like a decent mount

What’s the cover to the light handle called? I haven’t been able to find one

Rip off. Dyi for under $20 and works just as well. Made mine 5 years ago and couldn’t be happier. Folks save your money for other things. Ta ta

It’s really a waste of money. Dyi for under $20 and works just as well. Ta ta

For a while I thought you guys had no hook on there loll god damn lolll

Beat down breakaway is the best set up I have found so far !

what painters pole did you use before? :D

Thanks for sharing. How many colors on lead core are you using? Are you using kicker with trolling motor? I see you were not using your LS to watch your baits? Is this due to distance behind boat with your trolling setup?

So are you trolling twister tail baits with jigs ?? Or cranks ?

I miss your fly fishing videos

Good job man

How is this working currently after 9 months

Has anybody tried the delete with carb motor?

What day of fishing that was! Wind truly is a Walley fisherman’s best friend..

I haven’t read the comment so you may have been told several times, but the washer on the tether is wrong, it’s going to fail the way you have it. Washer on top wire between

Beautiful review. I just purchased this after your video. Lol love the part where you can remove so it doesn't get stolen because Colorado next to California is the leader in people stealing shit.

Great video.. can I use this just drifting? Or do I need to be trolling? Thank u

Great video.. can I use this just drifting? Or do I need to be trolling? Thank u

Do you think you could have disassembled without the engine stand? Im starting my breakdown this afternoon. Thank you so much for this video sir!

Where did you get the replacement lens for outside light.

Great video,can you add a link to the pole mount please?👊

Great video 👍 I’ve got the same boat and a 250 Yamaha and I also went with the Fishing Specialties pole last year. I use the magnetic plate up at the bow and the screw type in the back. I’ve had the magnets not hold good in rough waves I think because with our hulls the rods have to be pretty long. Mike sent me new magnets so we’ll see how they hold up this season. I don’t use my shuttle in the boat since I got 12” screens in the boat and only a 9” in the shuttle but that’s a great idea and system for sure !! 👍👍👍

I see your line is attached to two clips but I don't understand what keeps the planer board to your line after a fish hits. Please explain. Thanks

Great video, bud! Thanks for the info!

Guess its ethanol causing those issues man my OX66 pumps last 8years

Hey brother, been looking for an ox66 to put on a project and came across your videos. These are really great breakdowns…. I have a question about this diaphragm pump system…. why would the factory even design the motor for three diaphragm pumps when all it takes, is one pump to get it up to the VST tank… is it because it’s cheaper and manual vacuum…

I just bought a 1991 on Friday, its in pretty good condition but needs update and new lift jacks. Looking forward to our own touches.

Great information . Good job, thank you.

Finally, a decent Livescope mount. Good job displaying this product.

Thanks for the great explanation on using planner boards. I have fished inland lakes my whole life. But living near Lake Superior, I'd like to try it out there. But it is a different style of fishing than what I am accustomed to. This video is of great help to me in learning the art of big lake fishing.

The remote you have has an A and B button. Does the A button launch the clay and what function does the B button do? Thanks for the great video, well done sir.

👊 'Promo sm'

Just did this. Connected the trigger wire from the fuel pump to the trigger wire on the high pressure pump. 1 week later. No power to either pump. Got any ideas?

looks like you can loose this board the way that it's clip on, right? other boards has a swivel you run the line through

Just ran across this model at Bass Pro for $349.95. With my veterans discount, I was fortunate to pay just $314. Very heavy duty machine with terrific features for much less than I would have dreamed.

Just moved for college to Utah. Would love to use it to help me scout new areas I’m not familiar with

Just a FYI on Bed liner! As a Autobody restoration shop. Bed liner holds moisture under it!

Forgot to set the hook, give it a good yank 😂

Would use this often on the Wasatch Front in Utah and up in Yellowstone!

I want to see whats right underneath me, not 15 or 20 feet away. I do fish flooded timber but the lakes are small (1000 acres) with tons of structure. The fishing specialties down pole transducer was the best solution. Mike at fishing specialties is fantastic. He is the first person to explain side scan where I could understand it. That was after 20 or more videos on You tube on the subject.

Hello, I have a Yamaha Ox66, year 2002, I would like to remove the lift pumps on its engine. It worked fine. How can I get the sheets to seal where the pumps go? Thank you.

Montana spring bear in a month! Also from Colorado. Deciding between this and the ollin. Leaning towards this

Is that an aluminum base plate ?

Discount tackle my favorite shop been going there since the 90s